RF Wideband Power Amplifiler Board Radio Frequency 1M-1000MHz /10KHz－1GHz 10dBm

Description

Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
1M-1000MHz/10KHz－1GHz 10dBm RF Power Amplifiler
Popular
Popular
Product Introduction
1M-1000MHz 2W power amplifier
Description:
100% Brand New and High Quality
1-1000MHz RF Wideband Power Amplifier
Power: DC + 12V ~ + 15V
Current: 480mA (static) This current with the input frequency and power vary, that is, we usually say that the dynamic current value is less than 500mA.
Correlation composition composition composition composition Results Results Results Rhithers.ithers.itherest nights,
The figure below shows the small signal gain, the gain is basically around 35dB.
The following figure shows 12V, input 0DBm saturated power output, the whole band output power is greater than 30dBm.
The following figure shows 15V, input 0DBm saturated power output, the whole band output power is greater than 31dBm.
The following figure shows 15V, input 5DBm saturated power output, full-band output power is greater than 32dBm, 700MHz below greater than 33dBm (2W).
Package Included:
1 MHz -1000 MHz 2W RF power amplifier
10KHz－1GHz 10dBm Power Amplifiler
Application:
Supply voltage: + 12V
Current: 30mA
P-1 output: 10dBm
Because the design does not collide, the Frequency Limiting circuit is only struck by the blocking capacitor. Therefore, the frequency can go to 10KHz, 10KHz to 100MHz gain significantly due to little change. Its low VSWR combines perfectly with various circuits as an ideal buffer amplifier.
Package Included: Metal Melting Torch Mini Gold Furnace Graphite:
1 x gasket
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
1M-1000MHz/10KHz－1GHz 10dBm RF Power Amplifiler
Product Introduction
1M-1000MHz 2W power amplifier
Description:
100% Brand New and High Quality
1-1000MHz RF Wideband Power Amplifier
Power: DC + 12V ~ + 15V
Current: 480mA (static) This current with the input frequency and power vary, that is, we usually say that the dynamic current value is less than 500mA.
Correlation composition composition composition composition Results Results Results Rhithers.ithers.itherest nights,
The figure below shows the small signal gain, the gain is basically around 35dB.
The following figure shows 12V, input 0DBm saturated power output, the whole band output power is greater than 30dBm.
The following figure shows 15V, input 0DBm saturated power output, the whole band output power is greater than 31dBm.
The following figure shows 15V, input 5DBm saturated power output, full-band output power is greater than 32dBm, 700MHz below greater than 33dBm (2W).
Package Included:
1 MHz -1000 MHz 2W RF power amplifier
10KHz－1GHz 10dBm Power Amplifiler
Application:
Supply voltage: + 12V
Current: 30mA
P-1 output: 10dBm
Because the design does not collide, the Frequency Limiting circuit is only struck by the blocking capacitor. Therefore, the frequency can go to 10KHz, 10KHz to 100MHz gain significantly due to little change. Its low VSWR combines perfectly with various circuits as an ideal buffer amplifier.
Package Included: Metal Melting Torch Mini Gold Furnace Graphite:
1 x gasket
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.